Commission an elevator controller

The commissioning of an elevator controller is identical to the commissioning of a common door with access manager. The elevator controller appears in the door list, but under Others rather than under Common door.

With access manager and registration unit (without hardware ID)

Here you will find the relevant video instruction for this article.

  • You are logged into the resivo admin portal.
  • You have the Component management authorization.
  • You have the real estate’s REM setup card with you.
  • You have created the common door in the resivo admin portal and it has the status Planned.
  1. In the menu, click Doors.
  1. Hold the REM setup card at the registration unit.
  • The access manager appears in the Doors menu with the status New.
  1. In the resivo admin portal click Identify.
  • The access manager flashes green a couple of times.
  1. Click the access manager.
  • The following view opens:
  1. Select Planned component.
    Note: If the component has not yet been planned, you can do this with New component here.
  1. Select the earlier planned common door from the door list.
  1. Click Save.
  • The planned common door is connected to the access manager.
  • You can now open the common door with the master key or remotely by using the resivo admin portal.

With access manager and registration unit (with hardware ID)

Here you will find the relevant video instruction for this article.

  • You are logged into the resivo admin portal.
  • You have the Component management authorization.
  • You have the real estate’s REM setup card with you.
  • You have created the common door in the resivo admin portal and when doing so typed in or scanned the hardware ID.
  1. In the menu, click Doors.
  1. Hold the REM setup card at the registration unit.
  1. Reload the website of the resivo admin portal.
  • The planned common door has the status Online.
  • The planned common door is connected to the access manager.
  • You can now open the common door with the master key or remotely by using the resivo admin portal.

With access manager and compact reader

You can commission a common door with an access manager 92 32 and a compact reader 91 04 or 91 12 only after you have commissioned the common door with an access manager and at least one registration unit. Afterwards, you connect the compact reader to the access manager via the RS-485 interface. If you do not need the registration unit, you can uninstall it after the commissioning of the compact reader (subterminal).

NOTICE

The RS-485 interface of the compact reader allows for longer distance wiring as compared to a registration unit. The bus wiring to the access manager can be up to 1,200 meters long. In addition, with the compact reader you can bring mobile connectivity to your common door.

  • You have commissioned the common door with an access manager and at least one registration unit.
  • You are logged into the resivo admin portal.
  • You have the Component management authorization.
  • You have the real estate’s REM setup card with you.
  • Verify that the firmware version of the compact reader you want to install supports online components. The recommended version is BRCB04_12RD or later.
  1. Connect the compact reader to the access manager via the RS-485 interface as shown on the diagram.
RS-485 wiring of access manager (left) and compact reader (right)
  • For established communication (via RS-485) between the access manager and the compact reader, the LED Tx and Rx on the access manager must flicker (red marked).
Flickering RS-485 LED indicators
  1. Configure the DIP switches and rotary switch located on the front side of the compact reader (remove the red rubber cover) as shown on the diagram below.
    For the Interface RS-485 setting, go to Real estate>Doors>Configuration in the resivo admin portal. Complete the configuration and click Save.

Configuring the compact reader switches and settings

NOTICE

The peripheral address and the setting in the wheel "0 - F" must match as shown in the diagram.

  1. (Optional) Verify that your compact reader can open the door by using a physical media: for example, your REM setup card or the master key.
  1. Transfer the VCP to the compact reader.
  1. (Optional) Verify that mobile access functions properly.
    a) Assign a digital key for that common door through the resivo admin portal.
    b) Use the digital key with a smartphone and the mobile access app on the compact reader.
  1. (Optional) Uninstall the registration unit if it is not required.
  • The common door is in operation.
  • You can now open the common door with the master key or remotely by using the resivo admin portal.

NOTICE

Do not change the settings of the DIP switches. Otherwise, you will have to carry out the configuration again after a power outage at the compact reader.